View MIC4721_1839685.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC4721 1.5a 2mhz integrated switch buck regulator micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 ( 408 ) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com may 2007 1 m9999-052907-a general description the micrel MIC4721 is a high efficiency pwm buck (step- down) regulators that provid es up to 1.5a of output current. the MIC4721 operates at 2mhz and has proprietary internal compensation that allows a closed loop bandwidth of over 200khz. the low on-resistance internal p-channel mosfet of the MIC4721 allows efficiencies up to 94%, reduces external components count and eliminates the need for an expensive current sense resistor. the MIC4721 operates from 2.7v to 5.5v input and the output can be adjusted down to 1v. the devices can operate with a maximum duty cy cle of 100% for use in low- dropout conditions. the MIC4721 is available in the 10-pin msop package with a junction operating range from ?40c to +125c. data sheets and support doc umentation can be found on micrel?s web site at: www.micrel.com. features ? 2.7 to 5.5v supply voltage ? 2mhz pwm mode ? output current to 1.5a ? up to 94% efficiency ? 100% maximum duty cycle ? adjustable output voltage option down to 1v ? ultra-fast transient response ? ultra-small external components stable with a 1h inductor and a 4.7f output capacitor ? fully integrated 1.5a mosfet switch ? micropower shutdown ? power good pin ? thermal shutdown and current limit protection ? pb-free 10-pin msop package ? ?40 c to +125 c junction temperature range applications ? fpga/dsp/asic applications ? general point of load ? broadband communications ? dvd/tv recorders ? point of sale ? printers/scanners ? set top boxes ? computing peripherals ? video cards ___________________________________________________________________________________________________________ typical application 1.5a 2mhz buck regulator 76 78 80 82 84 86 88 90 92 94 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 5v in to 3.3v o efficiency
micrel, inc. MIC4721 may 2007 2 m9999-052907-a ordering information part number voltage temperature range package lead finish MIC4721ymm adj. ?40 to +125c 10-pin msop pb-free pin configuration fb en 6 5 1 sw vin sgnd bias 10 sw vin pgnd pgood 9 8 7 2 3 4 10-pin msop (mm) pin description pin number pin name pin function 1, 10 sw switch (output): internal power p-channel mosfet output switch. 2, 9 vin supply voltage (input): supply voltage fo r the source of the internal p-channel mosfet and driver. requires bypass capacitor to gnd. 3 sgnd signal (analog) ground. provides return path for control circuitry and internal reference. 4 bias internal circuit bias supply. must be by passed with a 0.1f ceramic capacitor to sgnd. 5 fb feedback. input to the error amplifier, c onnect to the external resistor divider network to set the output voltage. 6 en enable (input). logic level low will shut down the device, reducing the current draw to less than 5a. 7 pgood power good. open drain output that is pulled to ground when the output voltage is within 7.5% of the set regulation voltage. 8 pgnd power ground. provides the ground return path for the high-side drive current.
micrel, inc. MIC4721 may 2007 3 m9999-052907-a absolute maximum ratings (1) supply voltage (v in ) .......................................................+6v output switch voltage (v sw ) ..........................................+6v output switch current (i sw )............................................11a logic input voltage (v en ) .................................. ?0.3v to v in storage temperature (t s ) .........................?60c to +150c operating ratings (2) supply voltage (v in )..................................... +2.7v to +5.5v logic input voltage (v en ) ....................................... 0v to v in junction temperature (t j ) ........................ ?40c to +125c junction thermal resistance msop-10l ( ja )...............................................130 c/w msop-10l ( jc ) ................................................43c/w electrical characteristics (3) v in = v en = 3.6v; l = 1h; c out = 4.7f; t a = 25c, unless noted. bold values indicate ?40c< t j < +125c. parameter condition min typ max units supply voltage range 2.7 5.5 v under-voltage lockout threshold (turn-on) 2.45 2.55 2.65 v uvlo hysteresis 100 mv quiescent current v fb = 0.9 * v nom (not switching) 570 900 a shutdown current v en = 0v 2 10 a [adjustable] feedback voltage 2% (over temperature) i load = 100ma 0.98 1.02 v fb pin input current 1 na current limit in pwm mode v fb = 0.9 * v nom 3.5 5 a output voltage line regulation v out > 2v; v in = v out +500mv to 5.5v; i load = 100ma v out < 2v; v in = 2.7v to 5.5v; i load = 100ma 0.07 % output voltage load regulation 20ma < i load < 3a 0.2 % maximum duty cycle v fb 0.4v 100 % pwm switch on- resistance i sw = 50ma; v fb = 0.7v fb_nom (high side switch) 95 200 300 m ? m ? oscillator frequency 1.8 2 2.2 mhz enable threshold 0.5 0.85 1.3 v enable hysteresis 50 mv enable input current 0.1 2.3 a power good range 7 10 % power good resistance i pgood = 500a 145 250 ? over-temperature shutdown 160 c over-temperature hysteresis 20 c notes: 1. exceeding the absolute maximum rating may damage the device. 2. the device is not guaranteed to function outside its operating rating. 3. specification for packaged product only.
micrel, inc. MIC4721 may 2007 4 m9999-052907-a typical characteristics 84 85 86 87 88 89 90 91 92 93 94 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 3.3v in to 2.5v o efficiency 76 78 80 82 84 86 88 90 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 3.3v in to 1.8v o efficiency 72 74 76 78 80 82 84 86 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 3.3v in to 1.5v o efficiency 66 68 70 72 74 76 78 80 82 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 3.3v in to 1.2v o efficiency 0 10 20 30 40 50 60 70 80 90 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 output current (a) 3.3v in to 1v o efficiency 76 78 80 82 84 86 88 90 92 94 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 5v in to 3.3v o efficiency 0 10 20 30 40 50 60 70 80 90 100 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 5v in to 2.5v o efficiency 0 10 20 30 40 50 60 70 80 90 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 5v in to 1.8v o efficiency 0 10 20 30 40 50 60 70 80 90 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 5v in to 1.5v o efficiency 0 10 20 30 40 50 60 70 80 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 5v in to 1.2v o efficiency 0 10 20 30 40 50 60 70 80 0 0.2 0.4 0.6 0.8 1.2 1.4 1.6 output current (a) 1.0 5v in to 1v o efficiency
micrel, inc. MIC4721 may 2007 5 m9999-052907-a typical characteristics -0.10 0 0.5 1.0 1.5 2.0 output current (a) load regulation -0.08 -0.06 -0.04 -0.02 0.00 0.02 v o = 1.8v v in = 3.3v -0.050 line regulation -0.045 -0.040 -0.035 -0.030 -0.025 -0.020 -0.015 -0.010 -0.005 0.000 23456 input voltage (v) i out = 100ma i out = 1.5a v o = 1.8v 0.970 0.975 0.980 0.985 0.990 0.995 1.000 1.005 reference voltage vs. temperature 20 40 60 80 temperature (c) v in = 3.3v 0.995 0.996 0.997 0.998 0.999 1.000 1.001 1.002 2.5 3 3.5 4 4.5 5 5.5 6 input voltage (v) reference voltage vs. input voltage 1.90 1.92 1.94 1.96 1.98 2.00 2.02 2.04 switching frequency vs. temperature 20 40 60 80 temperature (c) 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.5 3 3.5 4 4.5 5 5.5 6 input voltage (v) switching frequency vs. input voltage 0 0.5 1.5 2.0 2.5 3.0 3.5 quiescent current vs. temperature 20 40 60 80 temperature (c) v in = 2.5v v in = 3.3v 1.0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0123456 input voltage (v) quiescent current vs. input voltage 0 20 40 60 80 100 120 140 160 180 200 switch on-resistance vs. temperature 20 40 60 80 temperature (c) r on @ 2.7v in r on @ 3.3v in r on @ 5v in 100 110 120 130 140 150 160 170 180 2.5 3 3.5 4 4.5 5 5.5 6 input voltage (v) switch on-resistance vs. input voltage r on @ i out = 1.5a r on @ i out = 0.1a 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 1.05 1.10 2.5 3 3.5 4 4.5 5 5.5 6 input voltage (v) enable threshold vs. input voltage turn-off turn-on 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 1.00 enable threshold vs. temperature 20 40 60 80 temperature (c) turn-off turn-on v in = 3.3v
micrel, inc. MIC4721 may 2007 6 m9999-052907-a functional characteristics
micrel, inc. MIC4721 may 2007 7 m9999-052907-a functional diagram vin vin bias en sw sw fb pgood pgnd enable and control logic pwm control p-channel current limit sgnd 1.0v 1.0v soft start bias, uvlo, thermal shutdown hsd ea MIC4721 block diagram
micrel, inc. MIC4721 may 2007 8 m9999-052907-a pin descriptions vin two pins for vin provide power to the source of the internal p-channel mosfet along with the current limiting sensing. the vin operating voltage range is from 2.7v to 5.5v. due to the high switching speeds, a 10f capacitor should be placed close to vin and power ground (pgnd) at each pin for bypassing. please refer to the section on layout recommendations. bias the bias (bias) provides power to the internal reference and control sections of the MIC4721. a 10 ? resistor from vin to bias and a 0.1f from bias to sgnd is required. en the enable pin provides a l ogic level control of the output. at a low level, the output is shut off and supply current at the vin pin is great ly reduced (typically <2a). a high level turns the output on. the enable pin must not be driven above the supply voltage. fb the feedback pin (fb) connects to the negative input of the internal error amplifier. the pin is connected to an external resistor divider, whic h sets the output voltage. a feedforward capacitor across the upper resistor in the divider is recommended for most designs. to reduce current draw, a 10k feedback resistor is recommended from the output to the fb pin (r1). the large resistor value and the parasitic capacitance of the fb pin can cause a high frequency pole t hat can reduce the overall system phase margin. by placing a feedforward capacitor, these effects can be significantly reduced. sw the switch (sw) pin connects directly to the inductor and provides the switching current necessary to operate in pwm mode. due to the high speed switching on this pin, the switch node should be routed away from sensitive nodes. this pin also connects to the cathode of the free-wheeling diode. pgood the power good pin pulls low to indicate the output voltage is within its regulation range. when power good is low, then the output voltage is within 10% of the set regulation voltage. for output voltages greater or less than 10%, the pgood pin is high. this should be connected to the input supply through a pull up resistor. a delay can be added by placing a capacitor from pgood-to-ground. pgnd power ground (pgnd) is the ground path for the mosfet drive current. the current loop for the power ground should be as small as possible and separate from the signal ground (sgnd) loop. refer to the section on layout recommendations for more details. sgnd signal ground (sgnd) is the ground path for the biasing and control circuitry. the current loop for the signal ground should be separate from the power ground (pgnd) loop. refer to the section on layout recommendations for more details.
micrel, inc. MIC4721 may 2007 9 m9999-052907-a application information the MIC4721 is a 1.5a pwm non-synchronous buck regulator. a regulated dc out put voltage is obtained by switching an input voltage supply, and filtering the switched voltage through an inductor and capacitor. figure 1 shows a simplified example of a non-synch- ronous buck converter and its input/output voltage. figure 1. simplified buck converter for a non-synchronous buck converter, there are two modes of operation; conti nuous and discontinuous. the mode refers to the state of current in the inductor. if current continuously flows through the inductor throughout the switching cycl e, it is in continuous operation. if the inductor current drops to zero during the off time, it is in disconti nuous operation. critically continuous is the point wher e any decrease in output current will cause it to enter discontinuous operation. the critically continuous load current can be calculated as follows. s in out out critical out f l v v v i ? = 2 2 _ where: f s is the switching frequency (2mhz for the MIC4721). l is the output inductance (henry). when i out is less than i out_critical , the buck converter operates in discontinuous mode and the inductor current goes to zero before the end of each switching cycle. when i out is greater than i out_critical , the converter operates in continuous mode and current always flows in the inductor. continuous or discontinuous operation determines how peak inductor current is calculated. continuous operation figure 2 illustrates the switch volt age and inductor current during continuous operation. figure 2. continuous operation the output voltage is regulated by pulse width modulating (pwm) the switch voltage to the average required output voltage. the switching can be broken up into two cycles; on and off. as seen in figure 3, the high side switch is turned on (on-time) and current flows from the input supply through the inductor and to the output. figure 3. on-time the inductor current is charged at the rate: ( ) l v v out in ? to determine the total on-time, or time at which the inductor charges, the duty cy cle needs to be calculated. the duty cycle can be calculated as: in out v v d = and the on time is:
micrel, inc. MIC4721 may 2007 10 m9999-052907-a s f d ton = therefore, peak to peak ripple current is: () l f v v v v i i s in out out in out pk pk ? + = ? peak-to-peak ripple current is used in calculating output voltage ripple. the peak current (or maximum inductor current) is equal to the output current plus ? the peak-to-peak current. () l f v v v v i i s in out out in out pk ? + = 2 the peak inductor current is used when selecting a suitable output inductor. figure 4 demonstrates circuit activity during the off-time. when the high-side internal p-channel mosfet turns off, current must flow th rough the free-wheeling diode, since inductor current must remain continuous. in this case, the inductor discharge rate is: () l v v d out + ? the total off time can be calculated as: s f d toff ? = 1 figure 4. off-time discontinuous operation discontinuous operation is when the inductor current discharges to zero at sometime during the off cycle. figure 5 demonstrates the switch voltage and inductor currents during discontinuous operation. figure 5. discontinuous operation when the inductor current (il) has completely discharged, the voltage on t he switch node rings at the frequency determined by the parasitic capacitance and the inductor value. in figur e 5, it is drawn as a dc voltage, but to see actual operat ion (with ringing) refer to the functional characteristics. discontinuous mode of oper ation has the advantage over full pwm in that at li ght loads, the MIC4721 will skip pulses as necessary, reducing gate drive losses, drastically improving light load efficiency. duty cycle considerations the p-channel mosfet inside the MIC4721 allows the fet to remain in the on-state indefinitely (100% duty cycle). this feature is useful for maintaining output voltage regulation in battery powered and other applications where the input voltage drops close to the output voltage. when the mosfet is operating at the 2mhz switching frequency, the maximum operating duty cycle is typically 82%. in situations where a duty cycle greater than the maximum operating duty cycl e is required, the MIC4721 will keep the fet turned on for additional cycles to maintain output voltage regulation. this effectively decreases the switching frequency, allowing a larger duty cycle. the output voltage ripple increases slightly when the MIC4721 is in pulse skipping mode.
micrel, inc. MIC4721 may 2007 11 m9999-052907-a efficiency considerations calculating the efficiency is as simple as measuring power out and dividing it by the power in. 100 = in out p p efficiency where input power (p in ) is: p in = v in i in and output power (p out ) is calculated as: p out = v out i out the efficiency of the mic2207 is determined by several factors. ? r dson (internal p-channel resistance) ? diode conduction losses ? inductor conduction losses ? switching losses r dson losses are caused by the current flowing through the high side p-channel mosfet. the amount of power loss can be approximated by: p sw = r dson i out 2 d where d is the duty cycle. since the MIC4721 uses an internal p-channel mosfet, r dson losses are inversely proportional to supply voltage. higher supply voltage yields a higher gate to source voltage, reducing the r dson , thus reducing the mosfet conduction losses. a graph showing typical r dson vs. input supply voltage can be found in the typical characte ristics section of this datasheet. diode conduction losses occur due to the forward voltage drop (vf) and the output current. diode power losses can be approximated as follows: p d = v f i out (1 ? d) for this reason, the low forward voltage drop schottky diode is the rectifier of choice. the low forward voltage drop will help reduce diode conduction losses, and improve efficiency. duty cycl e, or the ratio of output voltage to input voltage, determines whether the dominant factor in conduction losses will be the internal mosfet or the schottky diode. higher duty cycles place the power losses on the high side switch, and lower duty cycles place the ma jority of power loss on the schottky diode. inductor conduction losses (pl) can be calculated by multiplying the dc resistance (dcr) times the square of the output current: p l = dcr i out 2 also, be aware that there are additional core losses associated with switching current in an inductor. since most inductor manufacturers do not give data on the type of material used, approximating core losses becomes very difficult, so verify inductor temperature rise. switching losses occur twice each cycle, when the switch turns on and when the switch turns off. this is caused by a non-ideal world where switching transitions are not instantaneous, and neither are current transitions. figure 6 demonstrates (or exaggerates?) how switching losses due to the transitions dissipate power in the switch. figure 6. switching transition losses normally, when the switch is on, the voltage across the switch is low (virtually zero) and the current through the switch is high. this equates to low power dissipation. when the switch is off, voltage across the switch is high and the current is zero, again with power dissipation being low. during the transitions, the voltage across the switch (vs-d) and the current through the switch (is-d) are at midpoint of thei r excursions and cause the transition to be the highest instantaneous power point. during continuous mode, thes e losses are the highest. also, with higher load current s, these losses are higher. for discontinuous operation, the transition losses only occur during the ?off? transition since the ?on? transitions there is no current flow through the inductor. component selection input capacitor a 10f ceramic is recommended on each vin pin for bypassing. x5r or x7r dielectrics are recommended for the input capacitor. y5v dielec trics lose most of their capacitance over temperature and voltage and are therefore not recommended. also, tantalum and electrolytic capacitors alone are not recommended because of their reduced rms current handling, reliability, and higher esr. sma ller case size capacitors are recommended due to their lower esl (equivalent series inductance). please refer to layout recommendations for proper layout of the input capacitors.
micrel, inc. MIC4721 may 2007 12 m9999-052907-a output capacitor the MIC4721 is designed fo r a 4.7f output capacitor. x5r or x7r dielectrics are recommended for the output capacitor. y5v dielectrics lose most of their capacitance over temperature and voltage and are therefore, not recommended. smaller case size capacitors are recommended due to their lower esl. the MIC4721 utilizes type iii voltage mode in ternal compensation and utilizes an internal zero to compensate for the double pole roll off of the lc filter. for this reason, larger output capacitors can create inst abilities. in cases where a 4.7f output capacitor is not sufficient, the mic2208 offers the ability to externa lly control the compensation, allowing for a wide range of output capacitor types and values. inductor selection the MIC4721 is designed for use with a 1h inductor. proper selection should ensure the inductor can handle the maximum rms and peak currents required by the load. maximum current ratings of the inductor are generally given in two methods; permissible dc current and saturation current. permissible dc current can be rated either for a 40c temperature rise or a 10% to 20% loss in inductance. ensure the inductor selected can handle the maximum operating current. when saturation current is specified, make sure that there is enough margin that the peak current since at higher temperatures, the inductor will saturate at a lower current. diode selection since the MIC4721 is non-synchronous, a free-wheeling diode is required for proper operation. a schottky diode is recommended due to the low forward voltage drop and fast reverse recovery time. the diode should be rated to handle the average output current. also, the reverse voltage rating of the diode should exceed the maximum input voltage. please refer to the layout recommendations to minimize switching noise. feedback resistors the feedback resistor set the output voltage by dividing down the output and sending it to the feedback pin. the feedback voltage is 1.0v. ca lculating the set output voltage is as follows: ? ? ? ? ? ? + = 1 2 1 r r v v fb out where r1 is the resistor from v out to fb and r2 is the resistor from fb to gnd. the recommended feedback resistor values for common output voltages are available in the bill of materials at the end of this specification. although the resistance range of the fb resistors is very wide, r1 is recommended to be 10k. this minimizes the effect the parasitic capacitance of the fb node. resistor r2 can be calculated by: fb out fb v v v r r ? = 1 2 feedforward capacitor (c ff ) a capacitor across the resistor from the output to the feedback pin (r1) is recommended for most designs. this capacitor can give a boost to phase margin and increase the bandwidth for transient response. also, large values of feedforward capacitance can slow down the turn-on characteristics, reducing inrush current. for maximum phase boost, c ff can be calculated as follows: 1 200 2 1 r khz c ff = bias filter a small 10 ? resistor is recommended from the input supply to the bias pin along with a small 0.1f ceramic capacitor from bias-to-ground. this will bypass the high frequency noise generated by the violent switching of high currents from reaching the internal reference and control circuitry. tantalum and electrolytic capacitors are not recommended since these types of capacitors aren?t as effective at filtering high frequencies. loop stability and bode analysis bode analysis is an excellent way to measure small signal stability and loop response in power supply designs. bode analysis monitors gain and phase of a control loop. this is done by breaking the feedback loop and injecting a signal into the feedback node and comparing the injected signal to the output signal of the control loop. this will requi re a network analyzer to sweep the frequency and compare the injected signal to the output signal. the most common method of injection is the use of a transformer. figure 7 demonstrates how a transformer is used to inject a signal into the feedback network. figure 7. transformer injection a 50 ? resistor allows impedance matching from the network analyzer source. this method allows the dc loop to maintain regulation and allow the network analyzer to insert an ac signal on top of the dc voltage.
micrel, inc. MIC4721 may 2007 13 m9999-052907-a the network analyzer will then sweep the source while monitoring a and r for an a/r measurement. while this is the most common method for measuring the gain and phase of a power supply, it does have significant limitations. first, to measure low frequency gain and phase, the transformer needs to be high in inductance. this makes frequencies <100hz require an extremely large and expensive transformer. conversely, it must be able to inject high frequencies. transformers with these wide frequency ranges generally need to be custom made and are extremely expensive (usually to the tune of several hundred dollars!). by using an op-amp, cost and frequency limitations caused by an injection transformer are completely eliminated. figure 8 demonstrates using an op-amp in a summing amplifier configuration for signal injection. figure 8. op amp injection r1 and r2 reduce the dc volt age from the output to the non-inverting input by half. the network analyzer is generally a 50 ? source. r1 and r2 also divide the ac signal sourced by the network analyzer by half. these two signals are ?summed? together at half of their original input. the output is then amplified by 2 by r3 and r4 (the 50 ? is to balance the network analyzer?s source impedance) and sent to the feedback signal. this essentially breaks the loop and injects the ac signal on top of the dc output volt age and sends it to the feedback. by monitoring the feedback ?r? and output ?a?, gain and phase are measured. this method has no minimum frequency. ensure that the bandwidth of the op-amp being used is much greater than the expected bandwidth of the power supply? s control loop. an op-amp with >100mhz bandwidth is more than sufficient for most power supplies (which includes both linear and switching) and are more common and significantly cheaper than the injection transformers previously mentioned. the one disadvantage to using the op-amp injection method; is the supply voltages need to be below the maximum operating voltage of the op-amp. also, the maximum output voltage for driving 50 ? inputs using the mic922 is 3v. for measuring higher output voltages, a 1m input impedance is required for the a and r channels. remember to always measure the output voltage with an oscilloscope to ensure the measurement is working properly. you should see a single sweeping sinusoidal waveform without distortion on the output. if there is distortion of the si nusoid, reduce the amplitude of the source signal. you could be overdriving the feedback causing a large signal response. the following bode analysis show the small signal loop stability of the MIC4721. t he MIC4721 utilizes a type iii compensation. this is a dominant low frequency pole, followed by 2 zero?s and finally the double pole of the inductor capacitor filter, creating a final 20db/decade roll off. bode analysis gives us a few important data points; speed of response (gain bandwidth or gbw) and loop stability. loop speed or gb w determines the response time to a load transient. fa ster response times yield smaller voltage deviations to load steps. instability in a control loop occurs when there is gain and positive feedback. phase margin is the measure of how stable the given system is. it is measured by determining how far the phase is from crossing zero when the gain is equal to 1 (0db). typically for 3.3v in and 1.8v out at 1.5a; ? phase margin = 47 degrees ? gbw = 156khz gain will also increase with input voltage. the following graph shows the increase in gbw for an increase in supply voltage.
micrel, inc. MIC4721 may 2007 14 m9999-052907-a 5v in and 1.8v out at 1.5a load; ? phase margin = 43.1 degrees ? gbw = 218khz the non-synchronous MIC4721 regulator only has the ability to source current. this means that the regulator must rely on the load to sink current. this causes a non- linear response at light loads. the following plot shows the effects of the pole creat ed by the nonlinearity of the output drive during light load (discontinuous) conditions. 3.3v in and 1.8v out i out = 50ma; ? phase margin = 90.5 degrees ? gbw = 64.4khz feed forward capacitor the feedback resistors are a gain reduction block in the overall system response of the regulator. by placing a capacitor from the output to the feedback pin, high frequency signal can bypass the resistor divider, causing a gain increase up to unity gain. the graph above shows the effects on the gain and phase of the system caused by feedback resistors and a feedforward capacitor. th e maximum amount of phase boost achievable with a f eedforward capacitor is graphed below. by looking at the graph, phas e margin can be affected to a greater degree with higher output voltages. the next bode plot shows the phase margin of a 1.8v output at 1.5a without a feedf orward capacitor.
micrel, inc. MIC4721 may 2007 15 m9999-052907-a as one can see the typical phase margin, using the same resistor values as before without a feedforward capacitor results in 33.6 degrees of phase margin. our prior measurement with a feedforward capacitor yielded a phase margin of 47 degrees. the feedforward capacitor has given us a phase boost of 13.4 degrees (47 degrees ? 33.6 degrees = 13.4 degrees). output impedance and transient response output impedance, simply st ated, is the amount of output voltage deviation vs. the load current deviation. the lower the output impedance, the better. out out out i v z ? ? = output impedance for a buck regulator is the parallel impedance of the output capacitor and the mosfet and inductor divided by the gain: cout l dson total x gain x dcr r z || + + = to measure output impedance vs. frequency, the load current must be swept across the frequencies measured, while the output voltage is monitored. figure 9 shows a test set-up to measure output impedance from 10hz to 1mhz using the mic5190 high speed controller. figure 9. output impedance measurement by setting up a network analyzer to sweep the feedback current, while monitoring the output of the voltage regulator and the voltage across the load resistance, output impedance is easily obtainable. to keep the current from being too high, a dc offset needs to be applied to the network analyzer?s source signal. this can be done with an external supply and 50 ? resistor. make sure that the currents are ve rified with an oscilloscope first, to ensure the integrity of the signal measurement. it is always a good idea to monitor the a and r measurements with a scope while you are sweeping it. to convert the network analyzer data from dbm to something more useful (such as peak to peak voltage and current in our case): 707 . 2 50 1 10 10 ? = ? mw dbm v and peak to peak current: load r mw dbm v ? = ? 707 . 2 50 1 10 10 the following graph shows output impedance vs frequency at 2a load current sweeping the ac current from 10hz to 10mhz, at 1a peak-to-peak amplitude. from this graph, you can see the effects of bandwidth and output capacitance. for frequencies <200khz, the output impedance is dominated by the gain and inductance. for frequencies >200khz, the output impedance is dominated by the capacitance. a good approximation for transient response can be calculated from determining the frequency of the load step in amps per second: 2 sec / a f = then, determine the output impedance by looking at the output impedance vs frequency graph. next, calculate the voltage deviation times the load step; ? v out = ? i out z out the output impedance graph shows the relationship between supply voltage and out put impedance. this is caused by the lower r dson of the high side mosfet and the increase in gain with increased supply voltages. this explains why higher supply voltages have better transient response. cout l dson total x gain x dcr r z || + + = to properly measure ripple on either input or output of a switching regulator, a proper ring in tip measurement is required. standard oscilloscope probe s come with a grounding clip, or a long wire with an alligator clip.
micrel, inc. MIC4721 may 2007 16 m9999-052907-a unfortunately, for high frequency measurements, this ground clip can pick-up high frequency noise and erroneously inject it into the measured output ripple. the standard evaluation b oard accommodates a home made version by providing probe points for both the input and output supplies and their respective grounds. this requires the removing of the oscilloscope probe sheath and ground clip fr om a standard oscilloscope probe and wrapping a non-shielded bus wire around the oscilloscope probe. if there does not happe n to be any non-shielded bus wire immediately available, the leads from axial resistors will work. by maintaining the shortest possible ground lengths on the oscilloscope probe, true ripple measurements can be obtained.
micrel, inc. MIC4721 may 2007 17 m9999-052907-a recommended layout mic47 21 1.5a evaluation board top bottom
micrel, inc. MIC4721 may 2007 18 m9999-052907-a MIC4721 schemati c and b.o.m. for 1.5a output bill of materials item part number manufacturer description qty. c2012jb0j106k tdk (1) grm219r60j106ke19 murata (2) c1, c2 08056d106mat avx (3) 10f ceramic capacitor x5r 0805 6.3v 2 c7 0402zd104mat avx (3) 0.1f ceramic capacitor x5r 0402 10v 1 c2012jb0j475k tdk (1) grm188r60j475ke19 murata (2) c9 06036d475mat avx (3) 4.7f ceramic capacitor x5r 0603 6.3v 1 c8 vj0402a820kxaa vishay vt (4) 82pf ceramic capacitor 0402 1 d1 ssa33l vishay semi (4) 3a schottky 30v sma 1 l1 ihlp2525ah-01 1 vishay dale (4) 1h inductor 17.5m ? (l)6.47mm x (w)6.86mm x (h)1.8mm 1 r1, r4 crcw04021002f vishay dale (4) 10k ? 1% 0402 resistor 2 crcw04026651f crcw04021242f crcw04022002f r2 crcw04024022f vishay dale (4) 6.65 k ? 1% 0402 for 2.5v out 12.4 k ? 1% 0402 for 1.8 v out 20 k ? 1% 0402 for 1.5 v out 40.2 k ? 1% 0402 for 1.2 v out open for 1.0 v out 1 r3 crcw040210r0f vishay dale (4) 10 ? 1% 0402 resistor 1 u1 MIC4721ymm micrel, inc. (5) 1.5 2mhz integrated switch buck regulator 1 notes: 1. tdk: www.tdk.com 2. murata: www.murata.com 3. avx: www.avx.com 4. vishay: www.vishay.com 5. micrel, inc.: www.micrel.com
micrel, inc. MIC4721 may 2007 19 m9999-052907-a package information 10-pin msop (mm) micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com the information furnished by micrel in this data sheet is belie ved to be accurate and reliable. however, no responsibility is a ssumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel products are not designed or authori zed for use as components in life support app liances, devices or systems where malfu nction of a product can reasonably be expected to result in personal injury. life suppo rt devices or systems are devices or systems that (a) are in tended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significan t injury to the user. a purchaser?s use or sale of micrel produc ts for use in life support app liances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2007 micrel, incorporated.

▲Up To Search▲

Price & Availability of MIC4721

	To Download MIC4721 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .